| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/mlx5: Fix racy bitfields and tighten struct layout
Bitfield operations are not atomic, they use a read-modify-write
pattern, therefore we should be careful not to pack bitfields that
can be concurrently updated into the same storage unit.
This split takes a binary approach: flags that are only modified
pre/post open/close remain bitfields, flags modified from user
action, including actions that reach across to another device (ex.
reset) use dedicated storage units.
Note mlx5_vhca_page_tracker.status is relocated to fill the alignment
hole this split exposes.
Bitfield justifications:
migrate_cap: written only in mlx5vf_cmd_set_migratable() at probe
chunk_mode: written only in mlx5vf_cmd_set_migratable() at probe
mig_state_cap: written only in mlx5vf_cmd_set_migratable() at probe
Dedicated storage units:
mdev_detach: written in the VF attach/detach event notifier
mlx5fv_vf_event() at runtime
log_active: written in mlx5vf_start_page_tracker()/
mlx5vf_stop_page_tracker() during runtime dirty tracking
deferred_reset: written in mlx5vf_state_mutex_unlock()/
mlx5vf_pci_aer_reset_done() during runtime reset handling
is_err: set by tracker error handling and dirty-log polling at runtime
object_changed: set by tracker event handling and cleared by dirty-log
polling at runtime |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix UAF in binder_thread_release()
When a thread exits, binder_thread_release() walks its transaction stack
to clear the t->from and t->to_proc that correspond with the exiting
thread. However, a process dying in parallel might attempt to kfree some
of these transactions. And if one of them has no associated t->to_proc,
the t->to_proc->inner_lock will not be acquired.
This means that transaction accesses in binder_thread_release() after
t->to_proc has been cleared might race with binder_free_transaction()
and cause a use-after-free error as reported by KASAN:
==================================================================
BUG: KASAN: slab-use-after-free in binder_thread_release+0x5d0/0x798
Write of size 8 at addr ffff000016627500 by task X/715
CPU: 17 UID: 0 PID: 715 Comm: X Not tainted 7.1.0-rc5-00149-g8fde5d1d47f6 #30 PREEMPT
Hardware name: linux,dummy-virt (DT)
Call trace:
binder_thread_release+0x5d0/0x798
binder_ioctl+0x12c0/0x299c
[...]
Allocated by task 717 on cpu 18 at 67.267803s:
__kasan_kmalloc+0xa0/0xbc
__kmalloc_cache_noprof+0x174/0x444
binder_transaction+0x554/0x8150
binder_thread_write+0xa30/0x4354
binder_ioctl+0x20f0/0x299c
[...]
Freed by task 202 on cpu 18 at 90.416221s:
__kasan_slab_free+0x58/0x80
kfree+0x1a0/0x4a4
binder_free_transaction+0x150/0x294
binder_send_failed_reply+0x398/0x6d8
binder_release_work+0x3e4/0x4ec
binder_deferred_func+0xbd8/0x104c
[...]
==================================================================
In order to avoid this, make sure that binder_free_transaction() reads
the t->to_proc under the transaction lock. This will serialize the
transaction release with the accesses in binder_thread_release(). Plus,
it matches the documented locking rules for @to_proc. |
| In the Linux kernel, the following vulnerability has been resolved:
binder: fix UAF in binder_free_transaction()
In binder_free_transaction(), the t->to_proc is read under the t->lock.
However, once the t->lock is dropped, the to_proc can die in parallel.
This leads to a use-after-free error when we attempt to acquire its
inner lock right afterwards:
==================================================================
BUG: KASAN: slab-use-after-free in _raw_spin_lock+0xe4/0x1a0
Write of size 4 at addr ffff00001125da70 by task B/672
CPU: 20 UID: 0 PID: 672 Comm: B Not tainted 7.1.0-rc6-00284-g8e65320d91cd #4 PREEMPT
Hardware name: linux,dummy-virt (DT)
Call trace:
_raw_spin_lock+0xe4/0x1a0
binder_free_transaction+0x8c/0x320
binder_send_failed_reply+0x21c/0x2f8
binder_thread_release+0x488/0x7e0
binder_ioctl+0x12c0/0x29a0
[...]
Allocated by task 675:
__kmalloc_cache_noprof+0x174/0x444
binder_open+0x118/0xb70
do_dentry_open+0x374/0x1040
vfs_open+0x58/0x3bc
[...]
Freed by task 212:
__kasan_slab_free+0x58/0x80
kfree+0x1a0/0x4a4
binder_proc_dec_tmpref+0x32c/0x5e0
binder_deferred_func+0xc48/0x104c
process_one_work+0x53c/0xbc0
[...]
==================================================================
To prevent this, pin the target thread (t->to_thread) to guarantee the
target process remains alive. Undelivered transactions without a target
thread are already safe, as the target process can only be the current
context in those paths. |
| Uncontrolled resource consumption in Windows Remote Procedure Call allows an unauthorized attacker to deny service over a network. |
| Use after free in Windows Filter Manager allows an authorized attacker to elevate privileges locally. |
| Out-of-bounds read in Remote Desktop Client allows an unauthorized attacker to disclose information over a network. |
| Out-of-bounds read in Remote Desktop Client allows an unauthorized attacker to disclose information over a network. |
| Heap-based buffer overflow in Microsoft Trace Data Helper allows an authorized attacker to elevate privileges locally. |
| Heap-based buffer overflow in Microsoft Office allows an unauthorized attacker to execute code over a network. |
| Joomla Extension - jdownloads.com - RCE through file upload in jDownloads < 4.1.8 - Insufficient validation of frontend thumbnail uploads allowed users with upload permission to place executable files on the server. This results in PHP code execution. |
| Joomla Extension - jdownloads.com - Publishing of files without approval in jDownloads < 4.1.8 - Manipulated frontend submission parameters could bypass the intended publication and ownership rules. In particular, submissions could be published despite automatic publication being disabled, and ownership could be assigned contrary to the intended policy. |
| Joomla Extension - jdownloads.com - SSRF via external download URL field jDownloads < 4.1.8 - HTTP redirects when retrieving external download URLs could bypass validation of the original destination. This allowed server-side requests to internal or otherwise prohibited destinations and disclosure of their responses (SSRF). |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Latch disable_idle_d3 per device
When disable_idle_d3 was introduced in vfio-pci, it directly manipulated
the device power state with pci_set_power_state(). There were no
refcounts to maintain or balanced operations, we could unconditionally
bring the device to D0 and conditionally move it to D3hot. Therefore
the module parameter was made writable.
Later, in commit c61302aa48f7 ("vfio/pci: Move module parameters to
vfio_pci.c"), as part of the vfio-pci-core split, the writable aspect
of the module parameter was nullified. The parameter value could still
be changed through sysfs, but the vfio-pci driver latched the values
into vfio-pci-core globals at module init. Loading the vfio-pci module,
or unloading and reloading, with non-default or different values could
change the globals relative to existing devices bound to vfio-pci
variant drivers.
Runtime PM was introduced in commit 7ab5e10eda02 ("vfio/pci: Move the
unused device into low power state with runtime PM"), which marks the
point where power states became refcounted. PM get and put operations
need to be balanced, but the same module operations noted above can
change the global variables relative to those devices already bound to
vfio-pci variant drivers. This introduces a window where PM operations
can now become unbalanced.
To resolve this with a narrow footprint for stable backports, the
disable_idle_d3 flag is latched into the vfio_pci_core_device at the
time of initialization, such that the device always operates with a
consistent value.
NB. vfio_pci_dev_set_try_reset() now unconditionally raises the
runtime PM usage count around bus reset to account for disable_idle_d3
becoming a per-device rather than global flag. When this flag is set,
the additional get/put pair is harmless and allows continued use of the
shared vfio_pci_dev_set_pm_runtime_get() helper. |
| In the Linux kernel, the following vulnerability has been resolved:
rust_binder: clear freeze listener on node removal
Generally userspace is supposed to explicitly clear freeze listeners
before they drop the refcount on the node ref to zero, but there's
nothing forcing that. Currently, in this scenario the freeze listener
remains in the freeze_listeners rbtree and in the remote node's freeze
listener list, even though the ref for which the listener is registered
is gone. This could potentially lead to a memory leak due to a refcount
cycle. Thus, remove the freeze listener in this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: Fix sleep in atomic context in xhci_free_streams()
When a USB device with active stream endpoints is disconnected,
xhci_free_streams() is called from the hub_event workqueue to
free the stream resources. It calls xhci_free_stream_info()
while holding xhci->lock with irqs disabled.
xhci_free_stream_info() invokes xhci_free_stream_ctx(), which
calls dma_free_coherent() for large stream context arrays.
dma_free_coherent() can sleep (e.g. via vunmap), triggering
a BUG when called from atomic context.
Call trace:
dma_free_attrs+0x174/0x220
xhci_free_stream_info+0xd0/0x11c
xhci_free_streams+0x278/0x37c
usb_free_streams+0x98/0xc0
usb_unbind_interface+0x1b8/0x2f8
device_release_driver_internal+0x1d4/0x2cc
device_release_driver+0x18/0x28
bus_remove_device+0x160/0x1a4
device_del+0x1ec/0x350
usb_disable_device+0x98/0x214
usb_disconnect+0xf0/0x35c
hub_event+0xab4/0x19ec
process_one_work+0x278/0x63c
Fix this by saving the stream_info pointers and clearing the
ep references under the lock, then calling xhci_free_stream_info()
outside the lock where sleeping is allowed. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: sideband: fix ring sg table pages leak
xhci_ring_to_sgtable() allocates a temporary pages array and
uses it to build the returned sg_table with
sg_alloc_table_from_pages().
The error paths free the pages array, but the success path
returns the sg_table without freeing it. This leaks the temporary
array every time a sideband client gets an endpoint or event ring
buffer.
Free the pages array after sg_alloc_table_from_pages() succeeds.
The returned sg_table has its own scatterlist entries and does not
depend on the temporary array after construction. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/ops-common: handle extreme intervals in damon_hot_score()
Fix three issues in damon_hot_score() that comes from wrong handling of
extreme (zero or too high) monitoring intervals user setup.
When the user sets sampling interval zero, damon_max_nr_accesses(), which
is called from damon_hot_score(), causes a divide-by-zero. Needless to
say, it is a problem.
When the user sets the aggregation interval zero, the function returns
zero. It is wrong, since the real maximum nr_acceses in the setup should
be one. Worse yet, it can cause another divide-by-zero from its caller,
damon_hot_score(), since it uses damon_max_nr_accesses() return value as a
denominator.
When the user sets the aggregation interval very high, damon_hot_score()
could return a value out of [0, DAMOS_MAX_SCORE] range. Since the return
value is used as an index to the regions_score_histogram array, which is
DAMOS_MAX_SCORE+1 size, it causes out of bounds array access.
The issues can be relatively easily reproduced like below. The sysfs
write permission is required, though.
# ./damo start --damos_action lru_prio --damos_quota_space 100M \
--damos_quota_interval 1s
# cd /sys/kernel/mm/damon/admin/kdamonds/0
# echo 0 > contexts/0/monitoring_attrs/intervals/sample_us
# echo 0 > contexts/0/monitoring_attrs/intervals/aggr_us
# echo commit > state
# dmesg
[...]
[ 131.329762] Oops: divide error: 0000 [#1] SMP NOPTI
[...]
[ 131.336089] RIP: 0010:damon_hot_score+0x27/0xd0
[...]
Fix the divide-by-zero intervals problems by explicitly handling the zero
intervals in damon_max_nr_accesses(). Fix the out-of-bound array access
by applying [0, DAMOS_MAX_SCORE] bounds before returning from
damon_hot_score().
The issue was discovered [1] by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_pci: fix vq info pointer lookup via wrong index
Unbinding a virtio balloon device:
echo virtio0 > /sys/bus/virtio/drivers/virtio_balloon/unbind
triggers a NULL pointer dereference. The dmesg says:
BUG: kernel NULL pointer dereference, address: 0000000000000008
[...]
RIP: 0010:__list_del_entry_valid_or_report+0x5/0xf0
Call Trace:
<TASK>
vp_del_vqs+0x121/0x230
remove_common+0x135/0x150
virtballoon_remove+0xee/0x100
virtio_dev_remove+0x3b/0x80
device_release_driver_internal+0x187/0x2c0
unbind_store+0xb9/0xe0
kernfs_fop_write_iter.llvm.11660790530567441834+0xf6/0x180
vfs_write+0x2a9/0x3b0
ksys_write+0x5c/0xd0
do_syscall_64+0x54/0x230
entry_SYSCALL_64_after_hwframe+0x29/0x31
[...]
</TASK>
The virtio_balloon device registers 5 queues (inflate, deflate, stats,
free_page, reporting) but only the first two are unconditional. The
stats, free_page and reporting queues are each conditional on their
respective feature bits. When any of these features are absent, the
corresponding vqs_info entry has name == NULL, creating holes in the
array.
The root cause is an indexing mismatch introduced when vq info storage
was changed to be passed as an argument. vp_find_vqs_msix() and
vp_find_vqs_intx() store the info pointer at vp_dev->vqs[i], where 'i'
is the caller's sparse array index. However, the virtqueue itself gets
vq->index assigned from queue_idx, a dense index that skips NULL
entries. When holes exist, 'i' and queue_idx diverge. Later,
vp_del_vqs() looks up info via vp_dev->vqs[vq->index] using the dense
index into the sparsely-populated array, and hits NULL.
Fix this by storing info at vp_dev->vqs[queue_idx] instead of
vp_dev->vqs[i], so the store index matches the lookup index
(vq->index). Apply the fix to both the MSIX and INTX paths. |
| Adobe Experience Manager is affected by a reflected Cross-Site Scripting (XSS) vulnerability. If a low-privileged attacker is able to convince a victim to visit a URL referencing a vulnerable page, malicious JavaScript content may be executed within the context of the victim's browser. Scope is changed. |
| Adobe Experience Manager is affected by a DOM-based Cross-Site Scripting (XSS) vulnerability. An attacker could exploit this issue by manipulating the DOM environment to execute malicious JavaScript within the context of the victim's browser. Exploitation of this issue requires user interaction in that a victim must visit a crafted webpage. Scope is changed. |